Fluke PM-3370B Manual do Utilizador Página 131
- Página / 297
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
COMMAND REFERENCE 4 - 31
ABORt
Syntax:
ABORt
Description:
The ABORt command resets the trigger system and places it in the "IDLE" state.
Pending actions that were already started are finished immediately. The ABORt
command is not finished until the pending actions have been terminated.
Note: The commands
*
RST and ABORt have the same effect on the trigger
functions, except that ABORt does not affect the state of the
INITiate:CONTinuous command. So, when an ABORt command is sent
while the INITiate:CONTinuous is ON, the trigger system will leave the
IDLE state at once.
Example:
Send
→ ABORt Aborts the current acquisition.
Send
→ CONFigure:AC Configures for AC-RMS value.
Send
→ READ:AC? Initiates and reads the AC-RMS value.
Read
← <the measured AC-RMS value>
- $XWRUDQJLQJ 1
- &RPEL6FRSH 1
- ,QVWUXPHQW 1
- Printed in the Netherlands 2
- 1 ABOUT THIS MANUAL 3
- B CROSS REFERENCES 7
- C MANUAL CONVENTIONS 7
- D STANDARDS INFORMATION 7
- E SUMMARY OF SYSTEM SETTINGS 7
- 2 GETTING STARTED WITH SCPI 10
- PROGRAMMING 10
- 2.3 Error Reporting 14
- 2.4 Acquiring Traces 15
- 3 USING THE COMBISCOPE 20
- INSTRUMENTS 20
- INPut SENSe 24
- TRACe CALCulate 24
- 3.4 Acquisition 37
- 3.4.1.1 Triggering 39
- Figure 3.4 DC Coupling 41
- Figure 3.5 AC Coupling 41
- 3.4.1.2 Video triggering 42
- Figure 3.6 LF Reject 42
- Figure 3.7 HF Reject 42
- 3.4.1.3 The trigger modes 44
- Figure 3.8 Pre-triggering 46
- 3.4.1.5 External triggering 47
- • Peak detection is off 47
- PRINT sample(i); 54
- SENSe:AVERage:COUNt 56
- 3.6 Channel Selection 57
- 3.7 Signal Conditioning 58
- , i.e., 1 division 60
- 3.8 Time Base Control 61
- 3.9 Post Processing 64
- CALCulate block, but not 66
- 0,5 *2,236068 1,118034== 70
- 3.10 Trace Memory 75
- 3.11 Screen/Display Functions 80
- PROGRAM EXAMPLE: 83
- MEAS selections 83
- 3.12 Print/Plot Functions 85
- 3.13 Real-Time Clock 87
- 3.14 Auto Calibration 87
- 3.15 Status Reporting 89
- 3.17 Front Panel Simulation 98
- 4 COMMAND REFERENCE 101
- 4.2 Command Summary 105
- 4.3 Command Descriptions 113
- CAL? CALibration 115
- CLS Clear Status 116
- ESE Event Status Enable 117
- ESR? Event Status Register 118
- IDN? Identification 119
- OPC Operation Complete 120
- OPT? Option identification 121
- RCL Recall instrument setup 122
- RST Reset 123
- SAV Save instrument setup 125
- SRE Service Request Enable 126
- STB? Status Byte 127
- TRG Trigger 128
- TST? Self-test 129
- WAI Wait-to-continue 130
- CALCulate<n>:FEED 133
- CALCulate<n>:MATH:STATe 137
- CALibration[:ALL] 141
- CONFigure 143
- DISPlay:BRIGhtness 145
- DISPlay:MENU[:NAME] 146
- DISPlay:MENU:STATe 147
- DISPlay:WINDow2:TEXT[1]:CLEar 150
- DISPlay:WINDow2:TEXT[1]:DATA 151
- DISPlay:WINDow2:TEXT[1]:STATe 153
- FORMat[:DATA] 157
- HCOPy:DATA? 158
- HCOPy:DEVice 159
- INITiate:CONTinuous 160
- INITiate[:IMMediate] 161
- INPut<n>:COUPling 162
- INPut<n>:IMPedance 164
- INPut<n>:POLarity 165
- INSTrument:NSELect 166
- INSTrument[:SELect] 166
- MEASure? 167
- SENSe:AVERage[:STATe] 176
- SENSe:FUNCtion:OFF 178
- SENSe:FUNCtion[:ON] 178
- SENSe:FUNCtion:STATe? 178
- → *RST Switches channel 1 on 179
- SENSe:SWEep:OFFSet:TIME 180
- SENSe:SWEep:REALtime[:STATe] 182
- SENSe:SWEep:TIME 183
- SENSe:SWEep:TIME:AUTO 185
- → *RST Switches CH1 on 186
- → *RST Resets the instrument 189
- STATus:OPERation:CONDition? 190
- STATus:OPERation:ENABle 190
- STATus:OPERation[:EVENt]? 190
- STATus:OPERation:NTRansition 190
- STATus:OPERation:PTRansition 190
- STATus:PRESet 192
- STATus:QUEStionable:ENABle 193
- STATus:QUEStionable[:EVENt]? 193
- STATus:QUEue[:NEXT]? 195
- SYSTem:BEEPer 196
- SYSTem:BEEPer:STATe 196
- SYSTem:DATE 200
- SYSTem:ERRor? 201
- SYSTem:KEY 202
- COMMAND REFERENCE 4 - 103 203
- SYSTem:SET 205
- SYSTem:TIME 207
- SYSTem:VERSion? 208
- TRACe:COPY 209
- TRACe[:DATA] 210
- Reads offset 212
- TRACe:POINts 213
- TRIGger[:SEQuence[1]]:HOLDoff 219
- TRIGger[:STARt]:HOLDoff 219
- TRIGger[:SEQuence[1]]:LEVel 220
- TRIGger[:STARt]:LEVel 220
- TRIGger[:STARt]:LEVel:AUTO 220
- TRIGger[:SEQuence[1]]:SLOPe 222
- TRIGger[:STARt]:SLOPe 222
- TRIGger[:SEQuence[1]]:SOURce 224
- TRIGger[:STARt]:SOURce 224
- TRIGger[:SEQuence[1]]:TYPE 226
- TRIGger[:STARt]:TYPE 226
- → 525 → NTSC 230
- → 1050 → HDTV 230
- → 1125 → HDTV 230
- → 1250 → HDTV 230
- TRIGger[:STARt]:VIDeo:LINE 232
- APPLICATION PROGRAM EXAMPLES 234
- APPENDIX A 234
- A.2 Acquiring Waveform Traces 238
- A.5 Pass/Fail Testing 243
- APPENDIX B CROSS REFERENCES 246
- B - 2 CROSS REFERENCES 247
- CROSS REFERENCES B - 3 248
- B.2.1 ACQUIRE menu 248
- B - 4 CROSS REFERENCES 249
- B.2.2 CURSORS menu 249
- Programmable with the 249
- RCL and SYST:SET commands 249
- CROSS REFERENCES B - 5 250
- B.2.3 DISPLAY menu 250
- B - 6 CROSS REFERENCES 251
- B.2.4 MATHPLUS MATH menu 251
- CROSS REFERENCES B - 7 252
- B - 8 CROSS REFERENCES 253
- TRAC:COPY 255
- TRAC[:DATA]? 255
- TRAC[:DATA] 255
- CROSS REFERENCES B - 11 256
- B.2.9 TB MODE menu 256
- B - 12 CROSS REFERENCES 257
- B.2.10 TRIGGER menu 257
- CROSS REFERENCES B - 13 258
- B - 14 CROSS REFERENCES 259
- B.2.11 UTILITY menu 259
- CROSS REFERENCES B - 15 260
- Note: - 50 261
- only applicable for PM3394B 261
- APPENDIX C MANUAL CONVENTIONS 274
- C.2 Glossary of Symbols Used 277
- C.3 List of Tables 277
- C.4 List of Figures 278
- C.5 Documents Referenced 279
- APPENDIX D 280
- STANDARDS INFORMATION 280
- Elements 281
- APPENDIX E 283
- SUMMARY OF SYSTEM SETTINGS 283
- Numerics 286
Manuais e produtos relacionados com Medição, teste e controlo Fluke PM-3370B
(60 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.122 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais